FRENIC LIFT MANUAL PDF

FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Yozshule Dosho
Country: Namibia
Language: English (Spanish)
Genre: Art
Published (Last): 8 May 2010
Pages: 447
PDF File Size: 10.75 Mb
ePub File Size: 13.94 Mb
ISBN: 472-8-65491-964-6
Downloads: 54921
Price: Free* [*Free Regsitration Required]
Uploader: Kazihn

Accident or injury may result. Do not use a circuit breaker with a capacity exceeding the recommended capacity. Torque limit time 0.

FUJI ELECTRIC FRENIC-LIFT SERIES INSTRUCTION MANUAL Pdf Download.

Page 54 F codes: Refer to Chapter 2 Section 2. Page 77 [ 16 ] Run operation error Problem You incorrectly operated the inverter. Llft 31 These are provided for the DC link bus powered system. Brake control by output current Operation level 0 to ON delay time 0.

Page 35 Table 2. Use them in accordance with your system requirements.

Fuji Electric FRENIC-Lift series Instruction Manual

U, V and W frehic and that the grounding wires are connected to the ground electrodes correctly. Increase F26 Motor Sound Carrier frequency. In the torque control, data of some function codes related to the control may be enabled or disabled. Take an attention for this structure to connect wires to main output secondary terminals.

Note 2 To protect wiring, insert a molded case circuit breaker MCCB or an earth leakage circuit breaker ELCB with overcurrent protection of the type recommended for the inverter between the commercial power supply and the inverter. Enable data prot ection Note: Page 9 Select an inverter according to the applicable motor ratings listed in the standard specifications table for the inverter. Tuning offset angle of the magnet pole Before to proceed to running a synchronous motor, be sure to tune offset angle of the magnet pole.

  AEROSIL R812 PDF

Each function code consists of a 3-letter string. Torque bias gain adjustment BTBG. Terminal Arrangement And Screw Specifications 2. No part of this publication may be reproduced or copied without prior written permission from Fuji Electric Co.

Doing so could cause fire. You need to replace the option card. To use it follow the steps listed below. Doing so could cause failure.

Therefore, if a control signal cable or wire comes into direct contact with a live conductor of the main circuit, the insulation of the sheath or the cover might break down, which would expose the signal wire to a high voltage of the main circuit. Vrenic up L02 for correct data. Page 60 y codes: Immediately trip with alarm processing 1: Setting Up Slide Switches 2.

External View And Terminal Blocks 1. Chapter 4 Running The Motor U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly. CAN bus An abnormal communication with the main body of the inverter is detected when communication the CAN bus is used, and the inverter is stopped.

Table of Contents Add to my manuals Add.

Page 40 Table 2. Page 29 Follow the procedure below for wiring and configuration of the inverter. Init ialize all function code freic to t he factory defaults H04 Auto-resetting 0: Refer to Chapter 5, Section 5. Precautions for use Driving a V When driving a V general-purpose motor with an inverter using ex- general-purpose tremely long wires, damage to the insulation of the motor may occur. Page 81 [ 24 ] Out of control speed Problem An out of control error Liff failure occurs between the speed command and the speed feedback.

  FRSR LEAVE RULES PDF

Page Name of option Function and application Insert an MC in the power source side of the inverter in order to: Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances. Mounting the covers Put the front cover to the inverter case so that its bottom engages mahual the hinges provided on both sides of the case.

Lower the temperature around the motor.

Page 30 Grounding terminals G Be sure to ground either of the two grounding terminals for safety and noise reduction. In no event will Fuji Electric Co. Follow the procedure below for wiring and configuration of the inverter.

Put the front cover back in reverse order of. The inverter connector RJ supplies the power to the keypad through the extension manuql for keypad.

Chapter 6 Troubleshooting 1 First, check that the inverter is correctly wired, referring to Chapter 2, Section 2. Read through this instruction manual and be familiar with the handling procedure for correct use.

The operation level and thermal time constant can be set. Precautions For Use Precautions for use Driving a V When driving a V general-purpose liftt with an inverter using ex- general-purpose tremely long wires, damage to the insulation of the motor may occur.